Back to the list
Parking distance control
Parking distance control
Operating principle
Ultrasonic sensors, indicated by arrows 1, are fitted in the bumpers to detect obstacles near the vehicle.
The function alerts the driver via audible signals and a display representing the
area where the obstacle was detected.
Depending on the equipment, the system detects obstacles behind, in front and to the
sides of the vehicle.
The Park Assist system is only activated when the vehicle is driven at a speed below
approximately 6 mph (10 km/h).
The function does not take into account towing or carrying systems that are not recognised
by the system.
WARNING
This function is an additional driving aid.
Under no circumstances should it replace the driver's care or responsibility whilst
reversing.
The driver should always be ready for sudden incidents while driving: always ensure
that there are no small, narrow moving obstacles (such as a child, animal, pushchair,
bicycle, stone, post, etc.) in the blind spot when manoeuvring.
WARNING
An impact to the underside of the vehicle while manoeuvring (e.g. striking a post,
raised kerb or other street furniture) may result in damage to the vehicle (e.g. deformation
of an axle).
To avoid any risk of accident, have your vehicle checked by an approved dealer.
Location of the ultrasonic sensors 1
Ensure that the ultrasonic sensors indicated by the arrows 1 are not obscured (by dirt, mud, snow, a badly fitted/attached number plate, etc.),
impacted, modified (including paintwork) or obstructed by any accessory fitted to
the rear and/or, depending on the vehicle, to the front or sides of your vehicle.
Note: on vehicles equipped with the "360° camera" function 360° CAMERA, the analysis of the vehicle surroundings (zones A and B) is not displayed in the "Bird's eye view" or "Side view" mode.
Operation
The display 2 shows the vehicle surroundings and emits beeps.
Depending on the equipment, it may be necessary to travel a few metres before the
side detection is activated.
If all areas have a grey background, the whole area around the vehicle is being monitored:
- Display A: analysis of vehicle surroundings in progress;
- Display B: analysis of vehicle surroundings complete.
Obstacle detection
The system is able to detect most obstacles located near the rear and, depending on
the vehicle, near the front and sides of the vehicle.
The audible signal frequency will increase as the vehicle approaches on obstacle,
until it becomes a solid beep at approximately 20 cm for an obstacle detected on the
sides and approximately 30 cm for an obstacle detected to the front or rear.
The area where the obstacle has been detected is displayed (display C). Depending on the vehicle, the area is displayed in green, orange (or yellow depending
on the vehicle) or red, depending on the proximity of the detected obstacle.
Tip
In the event of a change in trajectory during a manoeuvre, the risk of collision with
an obstacle may be signalled late.
Special case of obstacles detected on the side
Depending on the direction of the wheels, the system determines the trajectory of
the vehicle and notifies the driver if there is a risk or not of a collision with
an obstacle 3 to the side of the vehicle.
If a side obstacle is detected:
- the beeps become faster and then sound continuously as the obstacle gets nearer. The area where the obstacle 3 has been detected is displayed (display D).
- if there is no risk of collision, no beep will sound when approaching the obstacle. Depending on the vehicle, the area where the obstacle 3 has been detected is shown interspersed.
Tip
In the event of a change in trajectory during a manoeuvre, the risk of collision with
an obstacle may be signalled late.
Activation/deactivation
Activation/deactivation from the multimedia screen 4
From the "Vehicle" world on your multimedia screen 4, press the "Driving assistance" menu then "Parking".
Activate or deactivate areas covered by the ultrasonic detectors.
Please refer to the multimedia instructions for further information.
Note: depending on the vehicle, the rear detection zone cannot be deactivated.
Parking distance control automatic deactivation
The system is deactivated:
- when the vehicle speed is above approximately 6 mph (10 km/h);
- depending on the vehicle, when the vehicle is stationary for more than approximately five seconds and an obstacle is detected (such as when in a traffic jam, etc.);
- when you are in N or P position;
- when an operating fault is detected.
Note: depending on the vehicle, if the vehicle is fitted with a towbar recognised by the
system, only the rear Park Assist function is deactivated.
Settings
WARNING
For safety reasons, carry out any adjustments while the vehicle is stationary.
Tip
Each time the vehicle is started, the function resumes the activation status saved
the last time the engine was stopped.
Adjusting settings from the multimedia screen 4
From the "Vehicle" world on your multimedia screen 4, press the "Driving assistance" menu then "Parking".
Please refer to the multimedia instructions for further information.
Deactivating the system sound
(depending on the vehicle)
Activate or deactivate the parking distance control sound.
Note: if you mute the sound, when approaching an obstacle you will be alerted only by the
display.
Parking distance control audio volume
Adjust the Park Assist volume using the volume bar.
Tip
Each time the vehicle is started, the function resumes the activation status saved
the last time the engine was stopped.
Special cases
You can manually deactivate sound alerts or, depending on the vehicle, the detection
zone concerned in the event that:
- towing, carrying or trailer equipment that is unrecognised by the system is present in front of the ultrasonic sensors;
- the ultrasonic sensors are damaged.
Note:even if the sound is muted, the displays will continue to warn you.
Operating faults
When the system detects a malfunction: either a sound signal warns you for about three
seconds when the reverse gear is engaged, accompanied by the "Check Parking sensors" message on the instrument panel, or the system does not produce a sound or display
when the reverse gear is engaged.
Check that the ultrasonic sensors are clean.
If it the fault persists, consult an approved dealer.
Advice
Tip
When the vehicle is travelling at a speed below approximately 6 mph (10 km/h), some
noises (motorcycle, lorry, pneumatic drill, etc.) may trigger the Park Assist system
audible warnings.
Tip
System servicing/repairs
- In the event of an impact, the alignment of the ultrasonic sensors may be altered and its operation may consequently be affected. Deactivate the function and consult an authorised dealer.
- Any work in the area where the ultrasonic sensors are located (repairs, replacements etc.) must be carried out by a qualified professional.
Only an authorised dealer is qualified to service the system.
System disturbance
Some conditions can disrupt or damage the system operation, for example:
- poor weather conditions (rain, snow, hail, black ice, etc.);
- some types of noise (motorcycle, lorry, pneumatic drill, etc.);
- fitting an non-compatible towing ball or hook.
Risk of false alarms or absence of warnings
If the system behaves abnormally contact an authorised dealer.
Limitation of the system operation
- The area around the sensors must be kept clean and free of any modifications in order to ensure the proper operation of the system.
- Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the system.
- The system may not detect obstacles that are too close to the vehicle.
- The system may not provide a warning when the other vehicles or obstacles are travelling at a significantly different speed.
- When there is a change in trajectory during a manoeuvre, the system may be slow in reporting obstacles.