Back to the list

Cruise control

  • 1
  • 2
  • 3
  • 4
  • 5

Cruise control

The cruise control function controls the engine and braking system to help you to maintain a driving speed that you have chosen, known as the cruising speed.
This cruising speed can be set at any speed above 19 mph (30 km/h).
Tip
You can link the cruise control function to the "Road sign detection" function DETECTION OF ROAD SIGNS.

Controls

1.
Cruise control On/Off switch.
2.
Switch to activate and decrease cruising speed (SET/˗).
3.
Switch to activate and increase cruising speed or to recall the memorised cruising speed (RES/+).
4.
Put the function on standby (with cruising speed stored) (0).
5.
Speed limiter On/Off switch.
WARNING
This function is an additional driving aid.
It can under no circumstances replace the driver's responsibility to respect speed limits or to be vigilant.
The driver must always be in control of the vehicle.
Cruise control must not be used in heavy traffic, on winding or slippery roads (black ice, aquaplaning, gravel) and during bad weather (fog, rain, side winds etc.).
There is a risk of accidents.

Switching on

Press the switch 1.
The 6 warning light appears in grey.
The "Cruise control ON" message appears on the instrument panel accompanied by dashes to indicate that the cruise control function is in operation and waiting to store a cruising speed.

Activating cruise control

At a steady speed above approximately 19 mph (30 km/h), press switch 2 (SET/˗) or switch 3 (RES/+): the function is activated and the current speed is taken into account.
The cruising speed replaces the dashes. Cruise control is confirmed when the memorised speed and warning light appear in green 6.
If you try to activate the function below 19 mph (30 km/h), the message "Invalid Speed" will be displayed and the function will remain inactive.

Driving

Once a cruising speed is registered and the cruise control function is active, you may lift your foot off the accelerator pedal.
WARNING
Please note that you must keep your feet close to the pedals in order to react in an emergency.

Adjusting the cruising speed

The cruising speed may be changed by repeatedly pressing the:
  • switch 2 (SET/˗) to reduce the speed;
  • switch 3 (RES/+) to increase the speed.
Note: press and hold one of the switches to modify speed by successive increments.

Exceeding the cruising speed

The cruising speed may be exceeded at any time by depressing the accelerator pedal.
While it is being exceeded, the cruising speed flashes in yellow on the instrument panel. Then, release the accelerator pedal: after a few seconds, the vehicle will automatically return to its set cruising speed.
WARNING
If the cruise control is no longer available (after several attempts to activate it), contact an Approved Dealer.
Tip
Temporarily not available
The system controls acceleration and deceleration of your vehicle using the engine and braking system. The system activates the brakes in order to maintain the set speed, the system applies limited braking. In the event of a steep descent, for example in a mountainous area, you must select a lower gear to benefit from engine braking.
To reduce the load imposed on the braking system and to prevent the brakes from overheating, the cruise control function may be temporarily interrupted and the "Check Cruise Control" message appears. The message disappears when the function becomes available again.
If the message remains, contact an approved dealer.

Putting the function on standby

The function is set to standby if you:
  • the switch 4 (0);
  • the brake pedal;
  • the clutch pedal for a prolonged period or if the vehicle is in neutral for a prolonged period on vehicles equipped with a manual gearbox;
  • shifting to neutral position, on vehicles equipped with an automatic gearbox.
The cruising speed is stored and displayed in grey on the instrument panel.
Returning to the cruising speed
If a speed is stored, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.). Press the switch 1 (RES/+) if the vehicle speed is above 19 mph (30 km/h).
When the speed is stored, cruise control activation is confirmed by the display in green of the cruising speed and, depending on the vehicle, the warning light 6 appears.
Note: if the speed previously stored is much higher than the current speed, the vehicle will accelerate more rapidly to reach this threshold.
When the cruise control function is on standby, pressing the switch 2 (SET/˗) to reactivate the cruise control function without taking into account the stored speed: the speed at which the vehicle is moving will be taken into account.

Switching off the function

The cruise control function is interrupted:
  • when you press the 1 switch. In this case, the speed is no longer stored;
  • when you press the 5 switch. In this case the speed limiter is selected and there is no stored speed.
The 6 warning light disappears from the instrument panel to confirm that the function has stopped.
WARNING
Putting the cruise control on standby or switching it off does not cause a rapid reduction in speed: you must brake by pressing the brake pedal.