BLIND SPOT WARNING
Using information from the sensors 1 installed on each side of the rear bumper, the system notifies the driver when another vehicle appears in detection zone A.
The system is activated when the vehicle’s speed is between approximately 19 mph (30 km/h) and 87 mph (140 km/h).
Special feature
Make sure that the 1 sensors are not obscured (by dirt, mud, snow, etc.).
If a sensor is obscured, the message “Blind spot clean sensor” will appear on the instrument panel. Clean the sensors.
This function is an additional driving aid.
This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.
Deactivation/activation
Press 3 to deactivate the function. Warning light 2 comes on.
Pressing again reactivates the function. Le warning light 2 disappears and the message “blind spot alert activated” is displayed on the instrument panel.
When the engine is started, the system remembers its last recorded position when the ignition was last switched off.
Indicator 4
An indicator light 4 is located on each rear view mirror 5.
Note: clean the rear view mirrors 5 regularly so that the indicators 4 can be seen.
Operation
This function gives a warning:
- when the vehicle speed is between approximately 19 mph (30 km/h) and 87 mph (140 km/h);
and
- when another vehicle is in the blind spot area A and travelling in the same direction as your vehicle.
The function does not notify the driver if the other vehicles are not moving.
If you overtake another vehicle, the indicator 4 will only come on if that vehicle remains for a long enough period in your vehicle’s blind spot A .
Display B
The function is activated and has not detected any vehicles.
Display C
First warning: when the direction indicator is not activated, the 4 warning light signals that a vehicle is detected in the blind spot.
Display D
When the direction indicator is activated, the 4 warning light flashes if a vehicle is detected in the blind spot on the side towards which you are about to steer. If you cancel the direction indicator, the function will return to the initial warning (display C).
The system’s detection range operates according to a standard lane width. When driving in a narrow lane, the function may warn you when a vehicle is detected further away than the nearest lane.
Conditions for non-function
- If the object is not moving;
- if traffic is heavy;
- the road is winding;
- if front and rear sensors both detect an object at the same time (e.g. when passing an articulated lorry).
-...
If the vehicle is equipped with a towbar recognised by the system, the message “Trailer: blind spot warning OFF” is displayed on the instrument panel informing you that the function is not operational. For information on the range of equipment adapted to your vehicle, we advise you to consult an approved Dealer.
Due to the presence of sensors in the bumper, it is advisable to entrust any operation on the bumper (repair, replacement, paintwork, etc.) to a qualified professional.
Operating faults
If the system detects a fault, the message “Check blind spot alert” is displayed on the instrument panel. Call an approved Dealer.
Note: when the engine is started, the indicator light 4, display B, flashes three times. It is normal.
- The system’s detection range operates according to a standard lane width. If you are driving in wide traffic lanes, the system might not be able to detect a vehicle in the blind spot.
- The system might be disrupted momentarily if it is exposed to strong electromagnetic waves (as beneath high-tension power lines) or to very poor weather conditions (heavy rain, snow etc.). Remain aware of driving conditions.
There is a risk of accidents.
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.
The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
The system should under no circumstances be taken to be an obstacle detector or an anti-collision system.
System servicing/repairs
- In the event of an impact, the alignment of the sensors may be changed and its operation may consequently be affected. Deactivate the function and consult an authorised dealer.
- Any work in the area where the sensors are located (repairs, replacements, etc.) must be carried out by a qualified professional.
Only an authorised dealer is qualified to service the system.
System disturbance
Some conditions can disrupt or damage the operation of the system, for example:
- complex surroundings (metal bridges, tunnels, roads with barriers at the edge, etc.);
- poor weather conditions (snow, hail, black ice, etc.).
Risk of false alarms or absence of warnings
In the event of the system behaving abnormally, deactivate it and consult an authorised dealer.
Limitation of the system operation
- The area around the sensors should be kept clean and free of any modifications in order to ensure the proper operation of the system.
- Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the system.
- When turning into a bend, the radars may temporarily cease to detect vehicles in adjacent lanes.
- The system may not provide a warning when the other vehicles are travelling at a significantly different speed.
- The vehicle is travelling on a winding road.
Deactivating the function
You must disable the function if:
- the area around the sensors has been damaged;
- the vehicle is fitted with a towbar that is not recognised by the system.