Back to the list

TYRE INFLATION KIT

  • 1
  • 2
  • 3
  • 4
  • 5

The kit repairs tyres when tread A has been damaged by objects smaller than 4 mm. It cannot repair all types of puncture, such as cuts larger than 4 mm, or cuts in tyre sidewall B.

Ensure also that the wheel rim is in good condition.

Do not pull out the foreign body causing the puncture if it is still in the tyre.

Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture.

You should therefore carefully check the condition of the tyre sidewalls before any operation.

Driving with underinflated, flat or punctured tyres can be dangerous and may make the tyre impossible to repair.

This repair is temporary.

A tyre which has been punctured should always be inspected (and repaired, where possible) by a specialist as soon as possible.

When taking a tyre which has been repaired using this kit to be replaced, you must inform the specialist.

When driving, vibration may be felt due to the presence of the repair product injected into the tyre.

The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit.

It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).

Avoid spillage on skin when handling the repair product bottle. If droplets do leak out, rinse them off with plenty of water.

Keep the repair kit away from children.

Do not dispose of the empty bottle in the countryside. Return it to your approved dealer or to a recycling organisation.

The bottle has a limited service life which is indicated on its label. Check the expiry date.

Contact an approved dealer to replace the inflation tube and repair product bottle.

Inflation kit C

Depending on the vehicle, in the event of a puncture, use inflation kit 1 located underneath the driver’s seat.

Vehicle fitted with a tyre pressure loss warning system

In the event of under-inflation (punctures, under-inflation etc.), the warning light appears on the instrument panel.TYRE PRESSURE LOSS WARNING.

Move the driver’s seat forward and fold down the seatback to access the inflation kit.

Open it.

Screw compressor adapter 3 to container 2 and clip onto compressor D.

The bottle must remain in an upright position.

Unscrew the valve cap on the tyre concerned.

Screw inflation adapter 4 onto the valve.

Before using this kit, park the vehicle at a sufficient distance from traffic, switch on the hazard warning lights, apply the handbrake, ask all passengers to leave the vehicle and keep them away from traffic.

If the vehicle is parked on the hard shoulder, you must warn other road users of your vehicle’s presence with a warning triangle or with other devices as per the legislation applying to the country you are in.

Do not pull out the foreign body causing the puncture if it is still in the tyre.

To connect the compressor, open the bonnet and connect the black clamp 10 to earth 5 BATTERY: troubleshooting.

Then connect red clamp 11 to terminal 6.

With the engine running, press switch 7 to start inflating.

After a maximum of 15 minutes, stop inflating and read the pressure on pressure gauge 9.

A pressure of at least 4.7 bar must be reached.

Note: while the bottle is emptying (approximately 30 seconds), the pressure gauge 9 will indicate briefly a pressure of up to 6 bars, then the pressure drops.

Before starting the engine, check that the handbrake is applied and the gear lever is in neutral or in position N for sequential gearboxes.

If the correct pressure cannot be achieved, repair is impossible. Do not drive the vehicle. Consult an approved dealer.

If the pressure is too high, press button 8 to lower the pressure.

Once the tyre is correctly inflated, remove the kit: slowly unscrew the inflation adapter 3 to prevent any product spatter and screw the tyre inflation hose 4 to the bottle opening 2 to prevent the product from escaping.

Affix the driving recommendation label to the dashboard where it can easily be seen by the driver;

Store the kit underneath the driver’s seat.

Start the vehicle immediately in order to the distribute the product in the tyre and, after 6 miles (10 km) or 10 minutes driving, stop to check the pressure. To do this, fit adapter 3 onto the tyre’s valve. If the pressure is less than recommended, readjust it. TYRE PRESSUREOtherwise, contact an approved dealer: the tyre cannot be repaired.

Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use.

Please be aware that a poorly tightened or missing valve cap can make the tyres less airtight and lead to pressure loss.

Always use valve caps identical to those fitted originally and tighten them fully.

Precautions when using the kit

The kit should not be operated for more than 15 consecutive minutes.

The container must be replaced after the first use even if liquid remains inside.

When driving, vibration may be felt due to the presence of the product injected into the tyre.

Following repair with the kit, do not travel further than 120 miles (200 km). In addition, reduce your speed and under no circumstances exceed 48 mph (80 km/h). The sticker, which you must affix in a prominent position on the dashboard, reminds you of this.

Depending on the country or local legislation, a tyre repaired with the inflation kit may need to be replaced.

Inflation kit E

Depending on the vehicle, in the event of a puncture, use the inflation kit located underneath the driver’s seat.

Vehicle fitted with a tyre pressure loss warning system

In the event of under-inflation (punctures, under-inflation etc.), the warning light appears on the instrument panel.TYRE PRESSURE LOSS WARNING.

With the engine running and the parking brake applied,

- Disconnect any accessories previously connected to the vehicle’s accessories sockets;

- refer to the information on the inflation kit compressor that is located under the driver’s seat and follow the instructions;

- inflate the tyre to the recommended pressure TYRE PRESSURE;

- after a maximum of 15 minutes, stop inflating and read the pressure (on the pressure gauge 12);

Note: while the bottle is emptying (approximately 30 seconds), the pressure gauge 12 will indicate briefly a pressure of 6 bar, then the pressure drops.

- Adjust the pressure: to increase it, continue inflation with the kit. To reduce it, press the button 13.

If a minimum pressure of 1.8 bar is not reached after 15 minutes, repair is not possible; do not drive the vehicle but contact an approved dealer.

Before using this kit, park the vehicle at a sufficient distance from traffic, switch on the hazard warning lights, apply the handbrake, ask all passengers to leave the vehicle and keep them away from traffic.

If the vehicle is parked on the hard shoulder, you must warn other road users of your vehicle’s presence with a warning triangle or with other devices as per the legislation applying to the country you are in.

Once the tyre is correctly inflated, remove the kit: unscrew the inflation adapter slowly from the container 14 to prevent any product spatter and store the container in plastic packaging to prevent product leaks.

- Affix the driving recommendation label (located under the container) to the dashboard where the driver can see it.

- Put the kit away.

- At the end of this initial inflation operation, air will still escape from the tyre. You must drive a short distance in order to seal the hole.

- Start immediately and drive at a speed between 12 to 37 mph (20 to 60 km/h) in order to distribute the product evenly in the tyre; after driving a distance of 2 miles (3 km), stop and check the pressure.

- If the pressure is higher than 1.3 bar but lower than the recommended pressure (refer to the label affixed to the edge of the driver’s door), adjust it. Otherwise, contact an approved dealer: the tyre cannot be repaired.

Precautions when using the kit

The kit should not be operated for more than 15 consecutive minutes.

The container must be replaced after the first use even if liquid remains inside.

Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use.

Please be aware that a poorly tightened or missing valve cap can make the tyres less airtight and may lead to pressure loss.

Always use valve caps identical to those fitted originally and tighten them fully.

Following repair with the kit, do not travel further than 120 miles (200 km). In addition, reduce your speed and under no circumstances exceed 48 mph (80 km/h). The sticker, which you must affix in a prominent position on the dashboard, reminds you of this.

Depending on the country or local legislation, a tyre repaired with the inflation kit may need to be replaced.