• 1
  • 2
  • 3
  • 4
  • 5

Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in.

Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection.

Adjusting your driving position

- Sit well back in your seat (having removed your coat or jacket etc.). This is essential to ensure your back is positioned correctly;

- adjust the distance between the seat and the pedals. Your seat should be as far back as possible while still allowing you to fully depress the pedals. The seatback should be adjusted so that your arms are slightly bent when you hold the steering wheel;

- adjust the position of your headrest. For maximum safety, your head must be as close as possible to the headrest;

- adjust the height of the seat. This adjustment allows you to select the seat position which offers you the best possible view;

- adjust the position of the steering wheel.

Make sure that the rear bench seat is locked in position correctly so that the rear seat belts will operate correctly. REAR BENCH SEATS: functions.

Incorrectly adjusted or twisted seat belts may cause injuries in the event of an accident.

Use one seat belt per person, whether child or adult.

Even pregnant women should wear a seat belt. In this case, ensure that the lap belt is not exerting too much pressure on the abdomen, but do not allow any slack.

Adjusting the seat belts

For correct adjustment and positioning of the seat belts at all seats:

- adjust the seats (seat position and seatback angle if available);

- sit with your back firmly against the seatback;

- move the chest strap 1 as close as possible to the base of the neck without it actually resting against it (if possible, adjust the height of the seat belt if needed) and make sure that the chest strap 1 is in contact with the shoulder;

- position the lap belt 2 so that it lies flat on the thighs and against the pelvis.

The seat belt must be worn as close to the body as possible. e.g. avoid wearing heavy clothing or keeping bulky objects under the belts, etc.


Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3).

If the belt jams, allow it to return slightly before attempting to unwind it again.

If your seat belt is completely jammed, pull slowly, but firmly, so that just over 3 cm unwinds. Allow it to wind up, then unwind it again.

If there is still a problem, contact an approved dealer.

ß Driver’s seat belt reminder and, depending on the vehicle, front passenger seat belt reminder

This appears on the central display 6 when the ignition is switched on and if the driver’s and/or front passenger’s seat belt(s) (if the passenger seat is occupied) is not fastened.

Depending on the vehicle, if the seat is occupied and one of these seat belts is not fastened or becomes unfastened while the vehicle is moving at a speed over approximately 12 mph (20 km/h), the ß warning light flashes and a beep sounds for approximately 120 seconds.

Note: an object placed on the passenger seat may activate the warning light in some cases, depending on the vehicle.

Rear seat belt reminder

(depending on the vehicle)

The 7 graphic is displayed on the instrument panel when the ignition is switched on. This informs the driver of the fastening status of each of the rear seat belts every time:

- the ignition is switched on;

- a door is opened;

- a rear seat belt is fasted or unfastened.

Understanding the graphic 7:

- white symbol: seatbelt fastened;

- black symbol: seatbelt unfastened.

When the vehicle speed is below approximately 12 mph (20 km/h), the graphic 7 appears during approximately 60 seconds every time one of the rear seat belts is fastened or unfastened.

When the vehicle speed reaches or exceeds 12 mph (20 km/h), if one of the rear seat belts is unfastened during the journey:

- the ß warning light flashes on the central display;


- a beep sounds for around 30 seconds;


- the 7 symbol is displayed for at least 60 seconds and the symbol for the seat concerned changes to black.

Always make sure that the rear passengers are properly fastened in and that the number of seat belts indicated corresponds to the number of rear seats occupied.

Adjusting the height of the front seat belts

Move button 8 to select the position you require so that chest strap 1 is worn as described above.

Make sure that the seat belt is locked in position correctly after you have adjusted it.


Press button 4 and the seat belt will be rewound by the inertia reel. Guide the belt.

Rear side seat belts

- For the first row of rear seats, it is mandatory to use seat belts 10;

- for the last row of rear seats, it is mandatory to use seat belts 9.

When the seat belt 10 is not in use, place the buckle 11 in its housing 12.

Conditions of use

Before using the rear side seat belts, make sure that for each one, the fixed buckle 13 is fully clicked into its catch 14.

The belts are then locked and unlocked in the same way as the front seats.

Check that the rear seat belts are positioned and operating correctly each time the rear bench seat is moved.

Access to the last row

To facilitate access to the last row of seats, detach the second row seat belt by unlocking it from its catch 15. Insert the detached part of the seat belt into the small bar on the fixed part of the belt.

Remember to lock the seat belt in place once more when a passenger is occupying the seat.

Centre seat belts

Unwind the seat belt slowly until the buckle locks in catch 16.

Rear seat functions REAR BENCH SEATS: functions

Make sure that the rear bench seats are locked in position properly so that the seat belts will operate efficiently REAR BENCH SEATS: functions.

The following information applies to the vehicle’s front and rear seat belts.

- No modification may be made to the component parts of the restraint system - belts and seats and their mountings - fitted originally. For special operations (e.g. fitting child seats) please contact an approved dealer.

- Do not use devices which give any slack in the belts (e.g. clothes pegs, clips, etc.), as a seat belt which is worn too loosely risks causing injury in the event of an accident.

- Never wear the shoulder strap under your arm or behind your back.

- Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around them.

- The belt should never be twisted.

- Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as they show any signs of wear.

- When the rear bench seat is being put back, make sure that the seat belts and buckles are correctly positioned so that they can be used properly.

- Make sure that the buckle is inserted into the appropriate catch.

- Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly secured.

- Make sure the seat belt catch is properly positioned (it should not be hidden away, crushed or flattened by people or objects).