STOP AND START FUNCTION
This system enables a reduced fuel consumption and lower greenhouse gas emissions.
The system is activated automatically when the vehicle is started.
While driving, the system stops the engine (standby) when the vehicle is at a standstill (traffic jam, traffic lights, etc).
System operating conditions
Engine standby is activated if:
- the vehicle has been driven since its last stop;
- the gearbox is in neutral;
- the clutch pedal is released;
and
- the vehicle speed is less than approximately 1.86 mph (3 km/h).
The warning light is displayed on the instrument panel to notify you that the engine is on standby.
The vehicle equipment remain operational while the engine is stopped.
The engine will restart when you press the clutch pedal and move into gear.
Special feature of the automatic engine re-start
Under certain conditions, the engine can restart on its own in order to guarantee your safety and comfort.
Do not drive off when the engine is on standby (warning light is displayed on the instrument panel).
If you get out of the vehicle, a beep and the message “IGNITION OFF” notifies you that the engine is on standby and has not been switched off.
This can occur especially when:
- the outdoor temperature is too low or too high (less than around 0 °C or higher than around 35 °C);
- the “Clear View” function is activated (please see the information on “Air conditioning” in Section 3);
- the battery is not sufficiently charged;
- the vehicle speed is above 3 mph (5 km/h) (downhill slope etc.);
- repeated pressing on the brake pedal or braking system requirement;
- the engine restart may be interrupted if the clutch pedal is released too quickly while a gear is engaged.
-...
Before leaving the vehicle, the engine must be stopped and not put on standby (please see the information on “Starting, stopping the engine” in Section 2).
Special features of vehicles with remote control
Some of these conditions prevent the engine from automatically restarting upon opening:
- one of the doors for vehicles using a key;
- the passenger side door for vehicles using a RENAULT card.
Conditions preventing the standby of the engine
Depending on the vehicle, certain conditions prevent the system from using the engine standby function, including when:
- reverse gear is engaged;
- the bonnet is not locked;
- for vehicles using a RENAULT card, the driver’s side door is not closed;
- for vehicles using a RENAULT card, the driver’s seat belt is not buckled;
- the outdoor temperature is too low or too high (less than around 0 °C or higher than around 35 °C);
- the battery is not sufficiently charged;
- the difference between the vehicle interior temperature and the automatic climate control instruction is too high;
- the “Clear View” function is activated (please see the information on “Air conditioning” in Section 3);
- the engine coolant temperature is too low;
- automatic particle filter cleaning is underway;
- the “Fast Idle Speed” function is activated (please refer to the information on “Fast Idle Speed” in section 2);
-...
Warning light is displayed on the instrument panel. This notifies you that engine standby is not available.
Special cases
- For vehicles using a RENAULT card, while the system is operating and the engine is in standby (traffic jam, traffic lights, etc.), if the driver gets out of their seat or unfastens their seatbelt and opens the driver's door, the ignition will be switched off. To restart and reactivate the Stop and Start system, press the start button (please refer to "Starting, stopping the engine" in Section 2).
- In the event of the engine stalling, if the system is operational, press down the clutch pedal as far as it will go to restart.
To fill up with fuel, the engine must be stopped (and not on standby): stop the engine (please refer to the information on “Starting and stopping the engine” in Section 2).
Deactivating, activating the function
Press switch 1 to deactivate the function. The message “STOP AND START DEACTIVATED” will appear on the instrument panel and the integrated warning light 2 on the switch will light up.
Pressing again will reactivate the system. The message “STOP AND START ACTIVATED” will appear on the instrument panel and the integrated warning light 2 on the switch 1 will go out.
The system is automatically reactivated each time the vehicle is started (see “Starting, stopping the engine” in Section 2).
Special note: engine on standby, press switch 1 to automatically restart the engine.
Operating faults
When the message “CHECK STOP AND START” appears on the instrument panel and the integrated warning light 2 lights up on the switch 1, the system is deactivated.
Please consult an authorised dealer.
Before leaving the vehicle, the engine must be stopped and not put on standby (please see the information on “Starting, stopping the engine” in Section 2).
In the event of an emergency, the engine can be restarted by pressing on the clutch pedal if the Stop and Start function is activated.