Back to the list

STOP AND START FUNCTION

  • 1
  • 2
  • 3
  • 4
  • 5

This system enables a reduced fuel consumption and lower greenhouse gas emissions. The system is activated automatically when the vehicle is started. During driving, the system stops the engine (standby) when the vehicle comes to a stop or is moving at a slow speed (traffic jam, traffic lights, etc), depending on the vehicle.

Conditions for engine standby

The vehicle has set off from where it was parked;

- the gearbox is in position D, M or N;

and

- the brake pedal is depressed (sufficiently hard);

Depending on the vehicle, if the warning light flashes and that the message “Press brake pedal” appears on the instrument panel, this indicates that the brake pedal is not sufficiently pressed;

and

- the accelerator pedal is not depressed;

and

- when the vehicle speed is zero during approximately one second or, depending on the vehicle, as soon as the vehicle speed is below approximately 3 mph (5 km/h).

The engine remains on standby if position P is selected, or if position N is selected with the handbrake engaged and the brake pedal released.

Warning light on the instrument panel is lit when the engine is on standby.

The vehicle equipment remain operational while the engine is stopped.

When the engine switches to standby, the steering assistance may no longer be operational.

In this case it becomes operational again when the engine is no longer on standby or the speed exceeds approximately 1 mph (1 km/h) (downhill, slope etc.).

If the engine is put in standby, the electronic parking brake (depending on the vehicle) is not applied automatically.

Keep your vehicle stationary when the engine is on standby (shown by the warning light on the instrument panel).

The engine MUST be stopped (not put in standby) before leaving the vehicle STARTING, STOPPING THE ENGINE: vehicle with key STARTING, STOPPING THE ENGINE: vehicle with card.

Preventing the engine from standing by

In certain situations, such as negotiating a crossroads for instance, it is possible (with the system activated) to keep the engine running so as to be ready to move off quickly.

Keep the vehicle stationary without pressing too hard on the brake pedal.

Conditions for coming out of engine standby

- when the driver’s door is opened;

or

- when the driver’s seat belt is unfastened;

- the brake pedal is released, position D or M engaged;

or

- brake pedal is released, position N engaged and parking brake released;

or

- parking brake is applied again, position P engaged, or position N engaged with parking brake applied;

or

- position R is engaged;

or

- the accelerator pedal is depressed;

or

- in manual mode, the gear change paddles are activated.

To fill up with fuel, the engine must be stopped (and not put in standby): you MUST stop the engine STARTING, STOPPING THE ENGINE: vehicle with key STARTING, STOPPING THE ENGINE: vehicle with card.

“AUTOHOLD” function activated “AUTOHOLD” FUNCTION, the brake pedal may be released and the engine standby maintained.

To exit engine standby, with the brake pedal released, press the accelerator pedal.

Conditions preventing the standby of the engine

Certain conditions prevent the system from using the engine standby function, including when:

- the driver’s door is not closed;

- the driver’s seatbelt is not fastened;

- reverse gear is engaged;

- the bonnet is not locked;

- the outdoor temperature is too low or too high;

- the battery is not sufficiently charged;

- the difference between the vehicle interior temperature and the automatic climate control instruction is too high;

- parking distance control is in operation;

- the altitude is too high;

- the gradient is too steep for vehicles fitted with an automatic gearbox;

- the “Clear view” function is activated AUTOMATIC CLIMATE CONTROL;

- the engine temperature is too low;

- the emission control system is being regenerated;

-...

Depending on the vehicle, warning light is displayed on the instrument panel. This notifies you that engine standby is not available.

The warning light may appear along with a message on the instrument panel:

- “Optimising Battery Recharge” to prioritise battery charging;

- “Prioritising Thermal Comfort” to prioritise air conditioning;

- “Prioritising running engine” to prioritise engine operations.

Deactivate the Stop and Start function for any operation performed in the engine compartment.

Special feature of the automatic engine re-start

Under certain conditions, the engine can restart on its own in order to guarantee your safety and comfort.

This can occur especially when:

- the outdoor temperature is too low or too high;

- the “Clear view” function is activated AUTOMATIC CLIMATE CONTROL;

- the battery is not sufficiently charged;

- the vehicle speed is above 3 mph (5 km/h) (downhill slope, etc.);

- repeated pressing on the brake pedal or braking system requirement;

-...

Depending on the vehicle, the warning light is displayed on the instrument panel to notify you of automatic engine restarting.

Depending on the vehicle, the warning light may appear along with a message on the instrument panel:

- “Optimising Battery Recharge” to prioritise battery charging;

- “Prioritising Thermal Comfort” to prioritise air conditioning;

- “Prioritising running engine” to prioritise engine operations.

The engine MUST be stopped (not put in standby) before leaving the vehicle STARTING, STOPPING THE ENGINE: vehicle with key STARTING, STOPPING THE ENGINE: vehicle with card.

Deactivating, activating the function

Press 1 to deactivate the function. The message “Stop & Start deactivated” appears on the instrument panel and the ignition warning light 1 appears.

Pressing again will reactivate the system. The message “Stop & Start Activated” appears on the instrument panel and the 1 switch disappears.

The system is automatically reactivated each time the vehicle is started using the start button STARTING, STOPPING THE ENGINE: vehicle with key STARTING, STOPPING THE ENGINE: vehicle with card.

Operating faults

When the “Check Stop & Start” message appears on the instrument panel and the 1 switch is on, this indicates that the system is deactivated.

Please consult an authorised dealer.

Special note: engine on standby, press switch 1 to automatically restart the engine.

EXPLORING THE STOP & START SYSTEM