Front seats

  • 1
  • 2
  • 3
  • 4
  • 5

Front seats

To move a seat forwards or backwards

Depending on the seat, lift the bar 1 or handle 4 to unlock the seat. Release the handle at the desired position and make sure that it is locked.

To adjust the height of the driver’s seat

Move the lever 3 as many times as required:
  • upwards to raise the seat base;
  • downwards to lower the seat.

To tilt the seatback

Depending on the seat, raise the lever 2 and tilt the seatback until it reaches the position required.
WARNING
After making adjustments, make sure that the seatbacks are correctly locked in place.
WARNING
To avoid all risk of injury, ensure that nobody is in the proximity of the moving parts. When moving the seat, make sure that nothing interferes with the moving parts and their locking.
WARNING
For safety reasons, carry out any adjustments while the vehicle is stationary.
We would advise you not to recline the seatbacks too far to ensure that the effectiveness of the seat belts is not reduced.
Nothing should be placed on the floor (area in front of the driver) as these objects may slide under the pedals during sudden braking manoeuvres, thus obstructing their use.

Central armrest 5

(depending on the vehicle)

To adjust the seat’s lumbar position

Lower the handle 6 to increase the support and lift it to decrease it.

Version with front bench seat for two

Depending on the vehicle, the central seatbacks may be folded down.
To fold down the seatback
Pull the tab 7 to unlock the seatback and lower the seatback A.
When lowering, tilt the headrest so that it is positioned under the centre console.
To raise the seatback
Lift the seat back and click it into place. Check that it is correctly locked.

Estate version flat position

Depending on the vehicle, the seatback on the passenger side may be folded down onto the seat base to create a flat position.
  • Deactivate the front passenger airbag;
  • hold the handle 4and move the seat as far back as possible;
  • hold the seatback at the top to guide it downwards;
  • pull the lever 2 and fold the seatback down forwards. While lowering, tilt the headrest 8 to position it underneath the dashboard;
  • press on the seat base to ensure that it is correctly positioned on the floor;
  • make sure that nothing prevents the seat from moving;
  • the seat locks automatically. Check that it is correctly locked.
WARNING
Be sure to hold the seatback when placing it in the flat position.
Risk of injury.
The label B on the seat base reminds you of these instructions.
Tip
Maximum weight on the seat in the flat position: 80 kg, with the weight evenly distributed.
The label B on the seat base reminds you of these instructions.

Repositioning the seat

Make sure that nothing prevents the seat from moving.
  • Pull the lever 2 and lift the seatback, ensuring that it is correctly locked;
  • reposition the seat base, placing your hand on the front of the seat base.
When the rear bench seat is folded down, move the front seats carefully.
Remember to reactivate the front passenger airbag before a passenger occupies the seat .
WARNING
Put your hand on the front of the seat base when repositioning it.
Risk of trapping.
WARNING
When the front seatback is in the flat position, you must deactivate the front passenger airbag.
Risk of serious injury if the airbag is deployed while objects are resting on the seatback in flat position.

Van version flat position

The seatback on the passenger side may be folded down onto the seat base to create a flat position.
  • Deactivate the front passenger airbag;
  • check that the floor is clear of any objects;
  • unlock the seat base by lifting the handle 10 and move the seat forwards, on the floor (movement D) while holding the rear section C;
  • press on the seat base to ensure that it is correctly positioned on the floor. There is a risk of the seatback being scratched if it is incorrectly positioned;
  • remove the headrest 9 from the seat;
  • store the headrest 9 in its housing underneath the seat base;
  • unlock the seatback by lifting the handle 10 again and position it horizontally (movement E).
The label F affixed on the side of the seat base reminds you of these instructions.
WARNING
Do not use the headrest housing 9 to store any other objects.
Risk of damage to the seat wiring.
WARNING
When the front seatback is in the flat position, you must deactivate the front passenger airbag.
Risk of serious injury if the airbag is deployed while objects are resting on the seatback in flat position.
The label F affixed on the side of the seat base reminds you of these instructions.
The rings 11 located on each side of the front passenger seat can be used to secure the load placed on the seat in the flat-floor position.
WARNING
For your safety, fasten down any objects transported with the seat in flat-floor position.
Tip
Maximum weight on the seat in the flat position: 80 kg, with the weight evenly distributed.
Maximum height limit for objects on the seat in the flat-floor position: 50 cm.
The label G affixed on the side of the seat base reminds you of these instructions.
To put the seat back in the comfort position, proceed in the reverse order. Check that the headrest is positioned correctly.
Remember to reactivate the front passenger airbag before a passenger occupies the seat .

Heated seats

Ignition on:
  • pressing the switch 12 on the required seat for the first time activates the heating system on high. Both of the built-in warning lights on the switch light up;
  • pressing the switch for the second time changes the heating to low. One integrated warning light is illuminated;
  • pressing for the third time turns the heating off.

Operating faults

When an operating fault is detected, the warning light of the switch 12 for the seat concerned goes out after approximately five seconds.
Consult an approved Dealer.